Tmedia, Tdev, and Tsig Web Portal: Protocol Stacks
ISDN FAS and NFAS
(Step 1) Allocate Physical Interfaces
(Step 2) Configure ISDN-PRI Signaling
OR *Configure NFAS
(Step 3) Modify NAP profile
(Step 4) Configure Network Access Points (NAPs)
ISDN Advanced Features
ISDN Overlap Sending
CAS
(Step 1) Allocate Physical Interfaces
(Step 2) Configuring a CAS stack
(Step 3) Modify NAP profile
(Step 4) Configure Network Access Points (NAPs)
SIP
(Step 1) Configure IP port range
(Step 2) Configure SIP Signaling
(Step 3) Modify NAP profile
(Step 4) Configure Network Access Points (NAPs)
SIP Advanced Features
SIP-I SIP-T
SIP Spiral and other SIP quirks
Remote NAT Traversal
Local NAT Traversal
DNS
SIP Authentication
SIP Service Affecting Parameters
When modifying the following parameters, the SIP stack will be deallocated and reallocated, resulting in a loss of active calls. Be careful when changing these parameters: Quirks
All Parameters
Header Parameters
Domain Name
Add rPort
DNS Parameters
Enabled
Use Cache
Cache Expire Time
Address and Port
SS7 ISUP
MTP2-MTP3-ISUP
(Step 1) Allocate Physical Interfaces
(Step 2) Configuring the MTP2 Layer
(Step 3) Configuring the MTP3 Layer
(Step 4) Configuring the ISUP Layer
(Step 5) Modify NAP profile
(Step 6) Configure Network Access Points (NAPs)
M2PA-MTP3-ISUP
(Step 1) Allocate Physical Interfaces
(Step 2) Configuring the M2PA Layer
(Step 3) Configuring the MTP3 Layer
(Step 4) Configuring the ISUP Layer
(Step 5) Modify NAP profile
(Step 6) Configure Network Access Points (NAPs)
MTP2-MTP3-M2PA (TDM/IP STP)
(Step 1) Allocate Physical Interfaces
(Step 2) Create MTP2 links
(Step 3) Configuring the M2PA Layer
(Step 4) Configuring the MTP3 Layer
M2UA-MTP2 Relay
(Step 1) Create Line Interfaces
(Step 2) Create MTP2 links
(Step 3) Create M2UA configuration
M2UA-MTP3-ISUP
(Step 1) Create M2UA configuration
(Step 2) Configuring the MTP3 Layer
(Step 3) Configuring the ISUP Layer
(Step 4) Modify NAP profile
(Step 5) Configure Network Access Points (NAPs)
M3UA-ISUP
(Step 1) Allocate Physical Interfaces
(Step 2a) Configuring the M3UA Layer - IPSP
(Step 2b) Configuring the M3UA Layer - ASP
(Step 2c) Configuring the M3UA Layer - SGP
(Step 3) Configuring the ISUP Layer
(Step 4) Modify NAP profile
(Step 5) Configure Network Access Points (NAPs)
SS7 Advanced Features
Configuring SPIROU
SS7 Service Affecting Parameters
When modifying the following parameters, some modules of the SS7 stack will be deallocated and reallocated, resulting in a loss of active calls. Be careful when changing these parameters: MTP2:
Connection Mode
Protocol Type
DPC Length
Timeslot Rate
Error Correction
Max Outstanding Frames
Discard Frame In Congestion
Cyclic Error: Nb of MSUs to retransmit
Cyclic Error: Nb of bytes to retransmit
MTP3 Network
Sub Service Field
Link type
Point code length
MTP3 Linkset
OPC
APC
MTP3 Link
MTP2 Link
Priority
MTP3 Route
DPC
Route To Adjacent
Sls Range
ISUP:
Primary Unit
Secondary unit
ISUP Interface
OPC, OPC length
DPC, DPC length
Available Test
UserPart
Network
ISUP Circuit Group:
First CIC
Line Service
Skip timeslot 16 CIC
Timeslots
CIC Options
SCCP-TCAP
MTP2-MTP3-SCCP-TCAP
(Step 1) Allocate Physical Interfaces
(Step 2) Configuring the MTP2 Layer
(Step 3) Configuring the MTP3 Layer
(Step 4) Configuring the SCCP Layer
(Step 5) Configuring the TCAP Layer (optional)
M2PA-MTP3-SCCP-TCAP
(Step 1) Allocate Physical Interfaces
(Step 2) Configuring the M2PA Layer
(Step 3) Configuring the MTP3 Layer
(Step 4) Configuring the SCCP Layer
(Step 5) Configuring the TCAP Layer (optional)
M3UA-SCCP-TCAP
(Step 1) Allocate Physical Interfaces
(Step 2) Configuring the M3UA Layer
(Step 3) Configuring the SCCP Layer
(Step 4) Configuring the TCAP Layer (optional)
SIGTRAN
Sigtran relays TDM signaling over IP.
If the Tmedia is used to forward signalling messages to a SoftSwitch, you may require to configure M2UA, M3UA or IUA before configuring H.248.
M2UA
(Step 1) Create Line Interfaces
(Step 2) Create MTP2 links
(Step 3) Create M2UA configuration
M3UA
(Step 1) Create Line Interfaces
(Step 2) Create MTP2 links
(Step 3) Create MTP3 configuration
(Step 4) Create M3UA configuration
IUA
(Step 1) Create Line Interfaces
(Step 2) Create IUA Configuration
When modifying the following parameters, some modules of the Sigtran stack will be deallocated and reallocated, resulting in a loss of active calls. Be careful when changing these parameters: SCTP
Service Type
udp_tunneling_port
Initial window space
MTU size
Domain name
M2UA
Node Type
M2UA SAP
SCTP Source Port
Maximum ACK delay
Edit IP Interfaces
M2UA LINK
MTP2 Link
Protocol Type
Interface Id
M2UA CLUSTER
Traffic Mode
Load Share Mode
M2UA PEER
Destination Port
Number of SCTP Streams
Self ASP Id
IP Header Type of Service (ToS)
Edit Destination Addresses
IUA SAP
SCTP Source Port
SCTP Primitive Timeout
Maximum ACK delay
Edit IP Interfaces
IUA CLUSTER
Traffic Mode
Load Share Mode
Minimum number of simultaneously active peer
IUA message queue size
IUA LINK
Interface Id
Line service
Variant
Side
IUA PEER
Destination Port
Valid ASP id required
Number of SCTP Streams
Edit Destination Addresses
Primitive timeout
IP Header Type of Service (ToS)
H.248 MEGACO
H.248 is a protocol used to interface a softswitch with a media gateway.
Media
TDM NAP (for ISUP/ISDN)
(Step 1) Allocate TDM Physical Interfaces
(Step 2) Modify NAP profile
(Step 3) Configure Network Access Points (NAPs)
VOIP NAP (for SIP)
(Step 1) Create IP Port Ranges
(Step 2) Modify NAP profile
(Step 3) Configure Network Access Points (NAPs)
CAS NAP
(Step 1) Allocate Physical Interfaces
(Step 2) Configuring a CAS stack
(Step 3) Modify NAP profile
(Step 4) Configure Network Access Points (NAPs)
Media Gateway
(Step 1) Configure Media Gateway for H.248 mode
(Step 2) Add a New Media Gateway Controller
(Step 3) Associate NAPs Resources to H.248 Configuration
Please note when modifying H.248 Service Affecting Parameters the H.248 stack will be deallocated and reallocated, resulting in a loss of active calls. Be careful when changing these parameters
Protocol Interoperability
Early Media
Q.1912.5 Profile A-B
''''''
In this section
Last updated
Was this helpful?