SCCP parameters
SCCP addressing, global title translation and subsystems. 56 parameters.
A
ASMB Timer
Default extended unit data reassembly timer (ITU92, ITU96, ANSI96, and TELCORDIA).
Attack Timer
Default attack timer (ITU96).
B
Broadband Support
Select to indicate that peer SCCP on the route has broadband support (should unselect for ITU88, ITU92, ANSI88, ANSI92 and ANSI 96).
C
Congestion Timer
Default SCCP congestion timer (ITU96).
CRD Timer
Default coordinated state change timer.
Customize msg importance
Replace the default message importance configuration.
D
Decay Timer
Default decay timer (ITU96).
Default Hop Count
Default Hop Count (between 1 and 15).
Default Status Enquiry Timer
The interval at which the periodic status request is sent to MTP Level 3 to enquire of the status of a point code.
Destination Point Code
The Destination Point Code (DPC) parameter is used to associate an object with a destination point code (DPC).
E
Enable Load Sharing
Specifies whether to enable load sharing mode (ITU96 only).
Encoding Scheme
Example Even Encoding Scheme
F
Format Type
The Format Type parameter (GTI) is used to set a global title format to be used by an SCCP GTT association.
Format Type (GTI)
*NOT_USED: Indicates that global title is not used.
G
GT Address (GTA)
Global Title Address (GTA) digits
GT Address (GTA) digits
Specifies whether to preserve GT or replace with Entity Global Title
I
Ignore SST Timer
Default ignore SST timer.
M
Max Msg Length
Maximum length of message delivered to the SCCP from this LSAP.
Msg importance for priority 3
Mapping of SIO priority 3 to importance of message.
Msg Importance: Ext Unit Data
Default importance for XUDT (Extended Unitdata) message.
Msg Importance: Ext Unit Data Service
Default importance for XUDTS (Extended Unitdata Service) message.
Msg Importance: Long Unit Data
Default importance for LUDT (Long Unitdata) message.
Msg Importance: Long Unit Data Service
Default importance for LUDTS (Long Unitdata Service) message.
Msg Importance: Unit Data
Default importance for UDT (Unitdata) message.
Msg Importance: Unit Data Service
Default importance for UDTS (Unitdata Service) message.
MTP3 Network
The MTP3 Network parameter is used to associate an MTP3 network with a higher level network in an SS7 system.
N
Net Indicator Bit Type
Net indicator bit is the MSB bit of CdParty's Global Title Address Indicator.
Numbering Plan
Example ISDN Numbering Plan
O
Output Network
Outgoing network of SCCP addresses.
P
Place PointCode in SCCP Header?
Select to set CdParty's Global Title Address Indicator PC equal to final MTP3 Destination Point Code Unselected leaves the DPC in SCCP header untouched.
Preserve Global Title
Specifies whether to preserve GT or replace with Entity Global Title
Primary Hardware Adapter
The Primary Hardware Adapter parameter is used to identify a main Tmedia hardware device to run an ISUP stack.
R
Replication Mode
The Replication Mode parameter is used to define the algorithm that will be used to select a point code/subsystem from the list of available point codes/subsystems.
Routing Indicator (RI)
Set RI bit in CdParty Global Title Address Indicator.
Routing Type
*Global_Title: Routing should be based on the global title.
S
SCCP Action Type
The Action Type parameter is used to set a behavior for an SCCP GTT Address Map.
SCCP Address
The SCCP Address parameter is used to set global title network addresses in an SCCP GTT address map.
SCCP Backup Point Code
The Backup Point Code is an alternate SP (Signaling Point) where to send the SCCP Messsage.
SCCP Concerned Point Code
A "Concerned" Point Code is SP that requires immediate notification if the affected subsystem or SP status changes.
SCCP Digit Range
SCCP GTT association actions: Start Digit
SCCP Net Indicator Bit
SCCP Network Indicator Bit The SCCP Network Indicator is one bit wide.
SCCP Network
The SCCP Network Parameter is used to associate an SCCP Network with an object in an SS7 system.
SCCP Output Network
The SCCP Output Network parameter is used to select an SCCP output network for a GTT address map on a system using the ITU96 protocol variant.
Secondary Hardware Adapter
The Secondary Hardware Adapter parameter is used to identify a secondary (backup) Tmedia hardware device to run an ISUP stack.
Set Destination Point Code?
Select to set MTP3 Destination Point Code for this message.
Set Sub-Service Type?
Select to set the MTP3 SubServiceField (SIO NI).
Set Sub-System Number?
Select to set CdParty's SSN Unselect to leave SSN untouched
SRT Timer
Default subsystem routing test timer.
SST Timer
Default subsystem status test timer.
Start and End Digits
The Start and End Digit parameters are only useful in an SCCP GTT Address Map with an action type in one of the following configurations: * FIX * VARIABLE_ASCENDING * VARIABLE_DESCENDING These parameters are used to define the first and las
Sub-System Number (SSN)
SSN value to match.
T
TCAP/MAP Operation Code (opcode)
TCAP/MAP operation code (opcode) value to match.
Translation Type
The translation type (TT) parameter is used in a network to indicate the preferred method of global title analysis.
U
Use Second Entity
Select to use the second entity (ITU96 only).
Use SIO priorities msg importance mapping
Select to enable SIO priority to importance mapping.
Last updated
Was this helpful?